Direction Desk

Here are the instructions from the manual of the Direction Desk for the keypad.

Keypad use

1. Initialization Procedure

Step	Operation	Motion
1	Press and hold ▲ and ▼ simultaneously for more than 3 seconds	Legs begin to move down at half speed of normal operation
2	Keep pressing ▲ and ▼	Legs move down to the lowest positions and rebound 2-5mm, then stop
3	Release ▲ and ▼ together	Initialization is completed

The initialization procedure must be completed before the first running after table is installed or parts replaced

2. Move up and down

Step	Operation	Motion
1	Press and hold ▲	Legs move up
2	Release ▲	Legs stop
3	Press and hold ▼	Legs move down
4	Release ▼	Legs stop

3. Set memory positions

Step	Operation	Motion
1	Press and hold ▲ or ▼, then release	Run the legs to the position you want the table surface to be
2	Click button S, then click button 1, 2 or 3 within the next 3 seconds	Position 1, 2, or 3 is saved

4. Move to the memorized positions

Step	Operation	Motion
1	Press and hold the button 1, 2, or 3	Legs return to the corresponding position saved

5. Toggle the display unit format

Step	Operation	Motion
1	Press and hold button S, then press and hold ▼ for about 3 seconds	The height information will be changed between centimeters and inches
2	Release the buttons	Completed

In inch format, the minimum height variation as the legs move up or down is 0.5 inches, while in centimeter format is 1 centimeter

6. Verify the keypad data to actual table height

Step	Operation	Motion
1	Set the table at any height, recommended at the bottom position	Measure the table actual height and write down the number in inches or in centimeters
2	Press and hold the button S, then press and hold ▲ for about 3 seconds	The first number starts flashing on the screen
3	Release the buttons, then click ▲ or ▼ to change the first number	The first number is being increased or decreased to the first number you measured
4	Click button S	The second number starts flashing on the screen
5	Click ▲ or ▼ to change the number	The second number is being increased or decreased to the second number you measured
6	Click button S	The third number starts flashing on the screen
7	Click ▲ or ▼ to change the number	The third number is being increased or decreased to the third number you measured
8	Click button S	Completed

Check the switch display format in inches or in centimeters and toggle to the unit you like and match to the actual measurement. In inch format, the minimum adjustable height is 0.5 inches, while in centimeter format is 1 centimeter.

7. Lock the stroke

Step	Operation	Motion
1	Press and hold ▲ or ▼, then release	Run the legs to the position you want the table surface to be
2	Press and hold button S, then press and hold 1 for about 3 seconds	Letter "L" is indicated on the screen. That means the position is locked at the lowest position that the table can be moved to
3	Release the button	Completed

• Legs aren't able to run below the locked position
• Memory Position(s) are/is below the locked position will be lost even after the table is unlocked, you need to follow SET MEMORY POSITIONS again to reset these memory positions

8. Unlock the stroke

Step	Operation	Motion
1	Press and hold button S, then press and hold 2, keep about 3 seconds	Letter "C" is indicated on the screen. That means the table's unlocked and can be moved in full range.
2	Release the buttons	Completed

9. Troubleshooting

Fault phenomenon	Handling
After connecting the power, press up and down and the legs have no response	Re-initialize the table Check if the connection is correct Contact Direction Desk
One leg moves while the other does not	Check if the connection is correct Ensure excess weight is not placed on one leg Contact Direction Desk
Table slides down itself	Check if the weight of the load on the table Exceeds 175 lbs or not Contact Direction Desk

#directiondesk #standupdesk #keypad